Rokonet ORBiT-14 Manual de usuario Pagina 31
- Pagina / 70
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Installation and Programming Manual
31
11
press this key to:
• enter selected information into the system
• accept the current selection and move to the next lower level in the programming
hierarchy
12
press this key to exit the current programming selection and move to the next higher
level in the programming hierarchy; doing so will NOT, in and of itself, store the
current information/data
13 0 through 9
use the numbered keys, 0 through 9, to key in numbers and/or special characters
when labeling zones and partitions
Table 3-2: LCD Keypad Programming Call-Outs
(refers to Figure 3-1 on page 30)
F
F
o
o
r
r
L
L
a
a
b
b
e
e
l
l
i
i
n
n
g
g
:
:
U
U
s
s
i
i
n
n
g
g
t
t
h
h
e
e
L
L
C
C
D
D
K
K
e
e
y
y
p
p
a
a
d
d
The ORBIT-Pro can be customized by displaying alphanumeric labels to better identify system zones and
partitions. “The Jones’s”, “Elm Lumber”, “Sales Dept”, and “Mastr Bedr” are just a few examples of the labels which
can be created to identify the system’s owner, business, location, a partition(s), or a zone.
The use of the LCD keypad for creating and editing labels differs from its use when programming system functions.
Table 3-3 lists the keys and indicators used in the labeling process, along with their functions. Refer to Figure 3-1
on page 30 to reference the item call outs.
The ORBIT-Pro permits a total of 74 characters (letters, numbers, and symbols) for use in labeling. A list of these
characters is found in the lower half of the table. A sample exercise is provided at the bottom of the page.
ITEM KEY/LED EXPLANATION IN THE LABELING MODE
2
mm
Power LED must be lit; will flash slowly during label creating and editing
3
mm
Arm LED
the system must be disarmed (Arm LED unlit) and in the
Installer Programming mode to perform labeling functions
8
the UP-arrow moves the cursor to the left;
the DOWN-arrow moves the cursor to the right
9
used for sequentially scrolling forward through the list of available characters (see
the list below)
10
used for sequentially scrolling backward through the list of available characters (see
the list below)
11
press this key to enter a completed label into the system
See
note
1 1 A B C D E F G H I J K L M
See
note
2 2 N O P Q R S T U V W X Y Z
See
note
3 3 ! “ & ’ : – . ? / ( )
See
note
4 4 a b c d e f g h i j k l m
See
note
5 5 n o p q r s t u v w x y z
6 through 0
if pressed, the “6”, “7”, “8”, “9” and “0” keys will toggle between producing their face
value in the display and a blank (space)
Table 3-3: LCD Keypad Callouts for Label Creating and Editing
Note: When labeling, each press of the 1, 2, 3, 4, or 5 keys will cause the corresponding characters to appear in
the sequence listed, followed by a blank (space).
To Create or Edit a Label (see pages 46 and 56 for additional information)
1. When in the labeling mode, move the UP- or DOWN-arrow until the cursor is under the character or space to
be changed. Pressing the UP-arrow moves the cursor to the left; press the DOWN-arrow to move right.
2. Select the desired character from the information given in the table. Note that the label for a partition can have
up to 12 characters while the label for a zone can have up to 10 characters.
3. When done, press [ENTER] to enter the label into the system. Press [SS] to cancel.
SS
# ENTER
DISARM
# ENTER
DISARM
- Main Board 1
- Zone Expansion 1
- Wireless Expansion 2
- Partitions 2
- Self Monitoring 5
- False Alarm Reduction 5
- Synoptic Map 5
- Figure 1-2 6
- Power Supply Expansion Module 10
- Event Log Expansion Module 10
- Printer Module 10
- X-10 Transmitter Module 10
- Total Auxiliary 18
- Maximum Current 18
- Draw per Branch 18
- Figure 2-1 19
- Figure 2-2 20
- Figure 2-3 21
- Zone Terminations 22
- Figure 2-5 23
- Figure 2-6 24
- Wiring Diagram 25
- PROGRAMMING METHODS 26
- Table 3-1 26
- * Not for UL Installations 26
- For Options 1 and 2 27
- 7- Apply Power to the System 27
- ↓↓ 28
- Figure 3-1: The LCD Keypad 30
- INSTALLER PROG: 33
- 1)SYSTEM ↓↓ 33
- IMPORTANT: 37
- (on pages 40 through 112) 39
- 1) System 40
- INSTALL PROG: 40
- SYSTEM: TIME DEFINE (cont’d) 41
- SYSTEM: SYSTEM CONTROL 42
- SYSTEM: SYSTEM LABEL 46
- SYSTEM LABELS: 46
- 1)PARTITION 1 46
- SYSTEM: SERVICE INFORMATION 47
- 2)ZONES ↓↓ 48
- ZONES: ZONE TYPE (cont’d) 51
- ZONES: ZONE SOUND 53
- Loop 54
- Response 54
- 2)SYSTEM ↓↓ 58
- Bell Follow 63
- No Telephone Line 63
- Communication 63
- Trouble Follow 63
- Ground Pulse 64
- Low Battery Follow 64
- AC Loss Follow 64
- Sensors Test 64
- UTILITY OUTPUT: PARTITION 65
- P=12345678 UO=xx 65
- Y 65
- 3) UO ↓↓ 66
- UTILITY OUTPUT: ZONE 67
- UTILITY OUTPUT: CODE 68
- UTILITY OUTPUT (cont’d) 69
- 4) Code Maintenance 70
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Rokonet ORBiT-14
(8 paginas)
(31 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.414 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales