Rokonet ORBiT-14 Manual de usuario descargar pdf (Pagina 35)

Installation and Programming Manual

INSTALLER PROGRAMMING TUTORIAL

The following exercise is designed to acquaint you with techniques for navigating through the Installer

Programming map (pages 37 and 38) while performing some common functions. The examples in the

tutorial are intended to be done in sequential order.

EXAMPLE 1: Setting a Zone’s Parameters

I want Zone 5 in my installation to have the characteristics of an

Interior Zone–so that activations occurring during the “AWAY”

(ARM) mode will cause an alarm, but those occurring during the

“STAY” (HOME) mode won’t.

From the initial “Installer Programming” display:

go to 2)ZONES by pressing the DOWN-arrow once. The

display will show:

Press [ENTER] to access the sub-categories under Zones.

This is the first of the nine sub-categories possible:

Read this step first before pressing any keys. To gain entry

into the Zone Types category, you can either press the

DOWN-arrow twice to access the following display,

and then press [ENTER]. If so, go directly to Step 4…

You can skip this display and the need for pressing

[ENTER]

and

go directly to Step 4 by simply pressing the “Quick Key” [3].

Below is the first display of the group of sub-categories

under ZONE TYPE.

Note the flashing cursor below the zone number. Type [0] [5] to

change to Zone 5, and press [ENTER]. See the NOTE on page 35,

at the end of the tutorial.

From this display,

use either the UP- or DOWN-arrow keys to choose among the 20

available Zone Types:

In the ORBIT-Pro, the type of zone described in the example is

known as 10)I+INSTANT (meaning Interior + Instant).

You may use either the UP- or DOWN-arrow key to scroll to the

desired Zone Type–or the “Quick Keys”, and enter [1] [0] instead. In

either case, this will appear on the display:

Press [ENTER] to confirm.

EXAMPLE 2 Setting the Acct No:

From here, let’s set the Account Number

used for reporting events to the Central

Station. To do so, we must go from the

ZONES category to the DIALER category.

Referring back to the map on page 37, we

can best accomplish this by first returning to

the “HOME” column at the left. To do so,

press the [S] key until the display shows the

original category selected [i.e. 2)ZONES].

Note that each press of the [S] key “raises”

your location in the map toward the “HOME”

column, from where we can proceed.

Read this step first before pressing any

keys. To gain entry into the Dialer category,

you can either press the DOWN-arrow three

times to access the following display,

and then press [ENTER]. If so, go directly to

Step 10…

you can skip this display and the need for

pressing [ENTER] and go directly to Step 10

by simply pressing the “Quick Key” [5].

From this display:

you can get to the ACCOUNTS

sub-category by pressing the

DOWN-arrow key, and [ENTER]

Simply by pressing [2], the corresponding

“Quick Key”. If so,

the above display will appear. Note the

flashing cursor is below the first digit

in the Account Number.

To change the Account Number, simply

enter the required digit(s). To correct an

error, use the UP-arrow to move the cursor

to the left and re-enter the proper digit(s).

You must press [ENTER] to confirm your

choice.

INSTALLER PROG:

1)SYSTEM ↓↓

INSTALLER PROG:

2)ZONES ××

SUBJECT: ZONES

1)ONE BY ONE ↓↓

SUBJECT: ZONES

3)ZONE TYPE ××

ZONE TYPE:

ZONE#=01 (00:01)

ZONE TYPE: 05

05)INSTANT ××

ZONE TYPE: 05

10)I+INSTANT ××

CUST. ACCOUNTS:

No:1 CODE:001111

SUBJ: DIALER

1)TEL. NUMBERS ↓↓

INSTALLER PROG:

5)DIALER ××

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 69 70

Comentarios a estos manuales

Sin comentarios

Rokonet ORBiT-14 Manual de usuario Pagina 35

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Rokonet ORBiT-14